Self-contained handle, lock and adjustable latch in a flush-fitting recess pan, with good resistance to water penetration. Easily fixed into a simple cut-out, with shaped latch tongue giving 3mm take-up against gasketed door edge. Stainless or carbon-steel models. Suits vehicle compartments & toolboxes, compressors, generators, other large enclosures.
Identical in function to locking models, but with no lock cylinder and reduced pan dimensions.
These are used when no security is required or where free-opening is mandatory (fire equipment, etc).
This is an optional feature which allows the ‘Drop-T’ unit to be secured from beneath, with no mounting holes, screws or rivets visible from outside.
Four weld-studs (M6 x 15 mm) are fitted to the flanges in same positions as normal mounting holes, giving better appearance, more security, and preventing entry of corrosion-causing agents.
Stud-fixing is an option on all ‘Drop-T’ models, including mild steel and powder coated versions.
The 3-way ‘Drop-T’ provides a complete latching system for the largest doors. Handle. lock, latch and flush recess pan form a self contained unit needing only a simple cut-out. Rods attached on site and adjustable for either LH or RH movement. Suits drop-down hatches, truck toolboxes and other large enclosures.
The multi-point ‘Drop-T’ is available as non-locking versions, usually with centre latching tongue and rods. Rods attached on site and adjustable for either LH or RH movement.
With multi-point versions the centre latching tongue can be removed to provide 2-way action only. The centre case can then be used with rods, or with standard end latches as illustrated. Adjustable for either LH or RH movement.
Where additional protection is desired for the lock cylinder, the ‘drop-T’ can be fitted with a protective cover. Two styles are available, either a sliding diecast plate (chrome) or a moulded flip-up cap illustrated. They can be used with all ‘drop-T’ models.
Very neat useful handles with circular ‘easy-fix’ escutcheon that are mounted through a standard pierced aperture. Lock cylinders are “shuttered” for weather-resistance, and handle can be water-sealed. Non-locking models available.
More substantial handles with circular, ‘easy-fix’ escutcheon that are mounted through a standard pierced aperture.
Lock cylinders are “shuttered” for weather-resistance, and handle can be water-sealed. Non-locking models available.
An extremely useful set that allows our large ‘T’ handle to be mounted so that the “arms” of the handle do not project above the surface of a panel. The steel recess pan is normally black powder-coated, with moulded gasket. Locking & non-locking models, supplied as boxed sets.
Good-looking handles with rectangular, surface-mounted escutcheons for either open- or concealed-fixing. Lock cylinders are “shuttered” for weather-resistance and there is choice of 38 mm (1.5 inch) or 44 mm (1.75 inch) hole centres
Widely-used cabinet handles with rectangular, surface-mounted escutcheons for either open fixing.
Lock cylinders are “shuttered” for weather-resistance and there is choice of 38 mm (1.5 inch) or 44 mm (1.75 inch) hole centres.
The most generally used industrial handles, with rectangular, surface-mounted escutcheons for either open- or concealed-fixing.
Lock cylinders are “shuttered” for weather-resistance and there is choice of 38 mm (1.5 inch) or 44 mm (1.75 inch) hole centres.
Sitting almost directly onto the panel surface, this design has absolutely minimum projection, avoiding risk of injury from the ‘arms’ of the T-handle.
With hidden mounting holes (or internal studs) it is ideal for roller shutters, vehicle side compartments and special cabinets.
Corrosion can be a major concern in some environments, such as marine industries or food processing plants, where these all-stainless handles will be very useful. The padlockable loop enables doors to be secured, with visible evidence that locking has taken place.
Created to provide a robust, modern design, the ‘Titan’ series is much stronger than normal handles. In particular, metal section at the base of the handle casting is more than twice usual thickness, preventing fracture and resisting lateral loads.
The full-length versions of the ‘Titan’ series have ‘tail’ turned inwards for good appearance and to reduce surface projection. The metal section at the base of the handle casting is more than twice usual thickness, preventing fracture and resisting lateral loads.
Two of our older designs, both made for large trucks, with heavier-duty fittings and extra metal thickness around shaft-retaining area to give greater strength.
The ‘Heavyweight’ series (at 504 grams) has been used by Massey Ferguson, Fodens, Scammel, and many American truck models. Fixing centres at 44mm (1.75 inch) only.
The ‘Ribbed’ series has been used by Bedford and military trucks, and by Ford Tractors. Fixing centres at 44mm (1.75 inch), or with spring return at 38mm (1.5 inch) centres.
These familiar designs have been fitted at various times to passenger cars, trucks, tractors, and to all types of ancillary equipment. Standard fixing centres 38mm (1.5 inch) and 44mm (1.75 inch), with alternative mounting escutcheons available, including concealed-fix options.
Two other long-established designs, both have unusual lengths of ‘lever’ which make them suitable for special vehicle applications and for ‘kit’ and ‘replicars’. Standard models are as shown, with alternative mounting escutcheons available, including concealed-fix options.
At one time immensely popular, these handles are now mostly used for restorations and reproductions of classic vehicles. Standard fixing centres are 44mm (1.75 inch) & 36mm (1.43 inch), with alternative mounting escutcheons available, including concealed-fix options.
Our diecast cams provide the simplest way of securing an enclosure door. They fit onto a plain, 8 mm-square shaft, and are clamped into position with the integral socket screw. A version is available with hole threaded M8, to suit corresponding round shaft.
The range of heavy steel cams (below) is normally fitted to our ‘drop-T’ series, but they can be used with any 8 mm-square shaft, normally threaded M10 with securing nuts to allow for adjustment and retention. Finish is bright zinc-plated.
An attractively styled handle, suitable for all personnel and compartment doors, and moulded in impact-resistant material with textured finish. This is a ‘free wheeling’ design, so the handle can never be forced when the button is in the locked position.
This is an attractive, self-contained ‘automotive’-style handle and recess ‘dish’ which is ideal for specialist vehicle applications. The handle lifts to operate an actuating lever, normally connected by wire-link to a remote latch, and the unit is easily fitted into a simple panel cut-out.
The illustrations show recommended panel-piercing dimensions for all models of ‘Drop-T’ latches, both locking and non-locking models.
Open fixing versions can be mounted using M6 or 1/4 inch dome-headed bolts (or equivalent rivets), and appropriate washers and securing nuts. Concealed-fixing versions have 4-off weld studs,
M6 x 15mm, at same positions.
To special order our drop-T models can be supplied with an 8mm-square shaft rather than with latch bar. Enquire to sales office.
The standard model illustrated is representative of a family of 2-way centre mechanisms, used with our end latches to provide slam action on two sides of a door or panel. Right-hand and left-hand systems are available, with many options to suit (volume) applications.
An exceptionally neat and compact unit which is used to make up 2-way or 3-way slam systems. ‘Quick-fit’ attachment points on case allow link bars to be quickly and easily attached, (generally with slam latches 3/22387). The integral slam-bolt provides centre-latching when fitted.
A new, left-hand version has recently been developed to suit European and U.S. requirements where fittings are normally on the left-side rear doors.
These versatile systems are assembled on site from standard end-latches, together with centre case (opposite) and connecting bars. The three slam bolts act together and are withdrawn simultaneously.
Left and right-hand versions are identical apart from position of centre bolt and direction of rotation of centre follow-bush. 2-way versions do not have centre slam-bolt.
A 2-way ‘conformity’ latch that is narrower and more completely enclosed than standard 2-way rod latches, with easily accessible points for attachments of rods or flat bars and fully in-line ‘throw’. Used for roller shutters, compartments and larger doors.
Again, a design which is an industry-standard for securing large doors requiring latching on two edges. This is a ‘deadbolt’ system with 10 mm diameter rods driven by centre bush, and held extended by action of a strong spring. Right-hand and left-hand models are available, with many special options.
A heavy-duty design which provides 3-point latching with an exceptional amount of ‘throw’. This is a ‘deadbolt’ system with 10 mm diameter rods driven by centre bush, and held extended by action of a strong spring. Right-hand and left-hand models are available, with many options.
This latch is widely used for large-size insulated enclosures, such as cold stores or containerised units, where a surface-mounted latch is preferable to avoid breaching the integrity of the door.
With slam action against a roller striker, this system can be used on doors flush-fit against the frame. There is an inside safety “punch” handle for emergency release.
Crossgate Road, Park Farm
Redditch, B98 7SN, United Kingdom
T: +44 (0) 1527 516060
E: sales@westonbodyhardware.com
